HVAC Services in San Antonio, Texas

Yes. We connect San Antonio homeowners and businesses in Bexar County with licensed, state-certified HVAC contractors. Our network covers all of Texas and is available for furnace repair, AC repair, annual maintenance, system inspection, and emergency heating and cooling service in San Antonio and surrounding communities. Call (855) 604-0166 to speak with a dispatcher who can connect you with an available HVAC contractor in your area.

In San Antonio's hot-humid climate, an annual AC tune-up before cooling season is the minimum. Condensate drain lines should be flushed every 3 to 4 months during the cooling season in Bexar County, since sustained humidity creates ideal conditions for algae growth that blocks the drain. Filters should be replaced every 30 to 45 days from May through September. A system that receives annual professional service plus regular filter changes will experience significantly fewer midseason failures than one that is only serviced reactively.

Proactively replacing a furnace over 15 years old eliminates emergency service costs, gives time to compare equipment and get multiple quotes, and avoids a no-heat situation in cold weather. Emergency furnace replacements average 15 to 30 percent higher cost due to expedited scheduling, limited equipment options, and reduced negotiating leverage. Planned replacements allow selection of preferred equipment and installation timing. If your furnace is over 16 years old and has required a repair in the past two seasons, request a replacement estimate now — even if the system is currently working. In Hot-Humid climates where failure during peak cold is a real health risk, the planning value alone justifies proactive action.

Furnace size in BTUs must be calculated through a Manual J load calculation accounting for home square footage, insulation levels, window area, infiltration rate, climate zone, and ceiling height — rules of thumb are not adequate. An oversized furnace short cycles, reducing comfort and accelerating heat exchanger wear. An undersized furnace runs continuously in extreme cold and cannot maintain setpoint. In Hot-Humid climates with high heating degree days, load calculations often yield higher BTU requirements than simple formulas suggest. Request that any contractor providing a replacement quote include a Manual J calculation or a documented load estimate. In pre-1980 homes with improved insulation or replaced windows, load calculations frequently show the home needs less BTU capacity than the system being replaced.

You can replace the furnace independently of the air conditioner, but if both systems are over 12 years old, replacing them together typically reduces total installation cost by 20 to 30 percent and ensures system compatibility. Modern high-efficiency furnaces are designed to work with matched-system coil configurations. Pairing a new furnace with an old AC coil can reduce system efficiency and may affect equipment warranties. Single-mobilization installation saves duplicate labor for sheet metal, refrigerant, and commissioning. If your AC is over 12 years old and the furnace requires replacement, request a combined quote. The incremental cost of adding the AC to a furnace replacement is almost always lower than scheduling it as a separate job the following season.

Furnace replacement typically costs $2,500 to $7,000 installed including equipment and labor. High-efficiency systems (96%+ AFUE) with two-stage or variable-speed operation run toward the upper end. Equipment cost accounts for 50 to 70 percent of total installed cost. Labor varies significantly by market — cold-climate cities with high HVAC demand tend to have higher installed costs. Additional costs arise when ductwork, flue venting, or gas line sizing requires modification. Get at minimum three itemized quotes including all modification costs for flue, ductwork, and gas supply. In San Antonio, Texas, local labor rates and fuel type strongly influence final price. For natural gas systems, confirm venting material compatibility with the new system's design.

The best time to replace a furnace is late summer to early fall before the heating season begins, or in spring after the heating season ends — both windows offer better technician availability and flexibility. HVAC contractors are least busy in late summer and spring. Scheduling outside peak winter demand (November through February in most cold-climate states) reduces wait times and avoids emergency-rate pricing. In Texas, target a replacement window 6 to 8 weeks before heating season onset. Avoid replacing during a no-heat emergency if possible — decisions made under pressure of cold temperatures reduce the opportunity to compare quotes.

A standard furnace replacement takes 4 to 8 hours for a straight swap — same fuel type, same location, no major ductwork or venting changes. Time is consumed by equipment removal, positioning, gas line connection, venting or flue modification, electrical connection, thermostat wiring, and startup commissioning. Complex installations with flue relining, ductwork modification, or new gas line runs can extend to two days. Plan for the home to be without heat for the installation day. The system should be tested and commissioned before the technician leaves. Request a startup checklist and combustion analysis reading to confirm the new system is operating within specification.

Removed furnaces are typically taken by the installing contractor for scrap metal recycling. Steel, copper, and aluminum components have scrap value. Most contractors include hauling as part of the installation price. Furnace components — steel cabinet, copper or stainless heat exchanger, aluminum blower wheel — are separated and sold to metal recyclers. Oil furnaces may require fuel tank disposal, which is subject to local environmental regulations. Confirm that old equipment removal and hauling is included in the installation quote before signing. Ask about any scrap credit if the system contains a copper heat exchanger — it may be factored into pricing.

Fuel type significantly affects furnace replacement scope — oil-to-gas conversions, propane replacements, and same-fuel swaps each have different costs, permit requirements, and venting considerations. Natural gas furnaces require a gas utility connection and properly sized gas piping. Oil furnaces require a flue system designed for higher combustion temperatures and an oil storage tank. Propane systems use the same combustion principles as natural gas but require pressure regulator adjustment and compatibility verification. For same-fuel replacement, the primary venting consideration is whether the new system requires PVC direct-vent (condensing 96% AFUE) rather than metal flue (80% AFUE) — these cannot share the same flue path. Confirm venting compatibility before finalizing equipment selection.

Replacing a functional furnace is financially justified when the efficiency gap between old and new equipment generates annual fuel savings that recover the replacement cost within 7 to 10 years. A 15-year-old furnace operating at 70% effective AFUE replaced by a 96% AFUE unit saves 26 cents of every dollar spent on fuel. In Hot-Humid climates with high annual heating costs, savings can range from $300 to $800 per year depending on fuel prices and heating degree days. Calculate estimated annual fuel savings, then divide the net installation cost (after any available rebates) by that figure to determine payback period. If payback is under 8 years and the system is already over 14 years old, proactive replacement is typically the better financial decision.

The average gas furnace lasts 15 to 20 years with proper maintenance. In climates with heavy heating demand, high humidity, or extreme temperature cycling, the lower end — 15 to 17 years — is more realistic. Heating demand hours directly correlate with wear on burners, heat exchanger, inducer motor, and blower. High-humidity climates accelerate corrosion on the heat exchanger. Freeze-Thaw climates impose additional stress from combustion air intake icing and large outdoor temperature swings. Track your furnace installation date. Begin planning for replacement when the system reaches 14 to 15 years, even if still operational — this allows time to research systems, get multiple quotes, and schedule installation outside peak demand windows.

Key signs a furnace needs replacement include age over 15 to 18 years, a cracked heat exchanger, rising repair frequency across successive seasons, consistent efficiency loss reflected in higher fuel bills, and inability to maintain setpoint in extreme cold. Aging furnaces experience compounding failures — each repaired component increases stress on adjacent aged components. A cracked heat exchanger is an immediate safety issue with no viable repair path. Efficiency degradation past 15 percent below nameplate rating represents a significant fuel penalty new equipment eliminates. If your furnace has needed two or more repairs in the past two heating seasons and is over 15 years old, request a replacement estimate alongside any further repair quotes. In Hot-Humid climates with long heating seasons, the efficiency payback on a new system is faster.